Showing posts with label Bumper Prep Fabrication Techniques. Show all posts
Showing posts with label Bumper Prep Fabrication Techniques. Show all posts

DIY - Homemade Dirt Bike Tug Strap


Have you gotten your dirt bike stuck in a mud pit out on a long trail ride? Did it take long to get it out? Did you lose all of your energy from pulling it out? If you answered yes to at least one of those questions, then I can help make life (well, riding.... but isn't riding your life anyway) a whole lot easier. If you don't know what a tug strap is, it's a piece of material that goes on the rear end of your seat that you can use to lift your dirt bike up.

First step is to get some material from a fabric or craft store. Should be pretty cheap because you only need a couple feet of it. You'll be looking for fabric that's similar to what tie-downs are made out of so it's strong enough. Two to three feet should be enough.

Next is to measure it up to the bike. Take the bolts off that hold the rear of the seat and side panels. Pull the rear of the seat up and take the material and put one end up to one of the seat bolt holes. Now, there are two ways you can do this, one will require a little more length in material, but will probably be more sturdy. First one is by putting the seat back down so the holes line up (ready for bolts to be screwed back in), then wrapping the material over the seat and lining it up with the other seat bolt hole. You should leave just enough slack in the strap over the seat so that you can fit a hand through it, but too loose will leave it hanging out, causing it to catch on your or another object not on the bike. Next is to mark the spots on the strap material where it lines up with the holes (a sharpie or marker will work). Now we'll look at the other option before we finish it...

The second way is to line up the start with the first hole, like we did for the first one. Instead of going over the seat now, first go under the seat with the strap, then wrap it around the top, and once again under the seat. So, it should be a complete loop around the bike (kinda' like what the Hot Wheels tracks did where you roll the car down the track and it does a loop, and then...Oh, never mind). Just remember to leave enough room for you hand. I guess the down-side to this route is that you have to wrap the strap around seat one more time when you take it off (big whoop!). The strap should now be lined up with the second hole; where we left off for the first strap...

After you have properly adjusted the strap and marked-up the holes, take it off. Now you will get the holes out to the correct size. You can do this by drilling them, or using a propane torch to heat a bolt/nail and burning a hole through the material.


Bumper Prep Fabrication Techniques


Sometimes you will need to refurbish or restore your bumper or other chrome-plated parts, and it can be done at your own personal garage, saving you some decent cash for restoration. When you are at it, it is advisable to always start with a good core and check for fit first.


For starters, get the bumper supported on a stand and work out flaws by tapping with a hammer and dolly. Remove the dents on the bumper and then use files to refine the metal. File the common flat areas with a flat file to remove any flaws.


For those corners which are hard to reach, a bull nose file may come in handy. After that, block sand with a power sander, starting with 80 grit. For the contoured areas, make use of round PVC blocks. You can use a long power air board file for the knocking out of remaining flaws. After it is done, give the bumper a wipe down using grease remover and wax or shine.


Next, you can work on the areas which require attention such as bumper guards and their fitting. If it fits badly, you can add some wire and weld it to the inner edge. When all fits well, you can attach the bumper onto a bumper rack (if you have one) and clamp it. Cut down the copper in 180 grit, and find low spots at the same time. During plating and electric process, copper will tend to build up on the outer edges due to the amperage draws. You can take some photos to know where are the areas you want to work on first. Continue to block sand until it is quite smooth.

Next, do plating if necessary as you won't be able to apply primer using a spray gun. If there are any scratches or strikes, you will need to coat the whole bumper and block it once more. Then, for inspection, wet it down. Check for dips and other problems, and tweak them into perfection.


For copper build ups, you can use a smooth sander to knock them down nicely. It will leave you with a surface that has small curly cue on it when you are done. Put a strike on the bumper so that the smoothness can be seen and compared. Grit (320) and sand (400) the bumper and get ready for polishing. After a final wet down, the bumper should look great. Polish the copper until it has a clear and mirror-like finish. Recommended are tools like the RotoSet as well as the Roto Star from Shunner, both which may be the best tool for the job.

The smaller grooves as well as the nooks and crannys can be settled with the small RotoSet. You can use many bars of compounds. Start with rough to medium, to fine and final color from left to right. You can make use of a variety of buffs to alter the amount of space in between the threads of the buff, ranging from aggressive to refined, so you can work by trial and error to achieve the best results.

It is advisable not to use compounds of different nature on the same wheels, because once there is a certain grit coated on, it will be ingrained. You should also clean the buff in between rounds. Using a bit of 600 grit, finish off the bumper and give it a nice polish for a mirror-like finish. Apply compound now and wipe the copper down using grease remover and wax intermittently. Keep in mind that these techniques work within a professional level street rod shop so they are proven methods.

At the same time, keep your eyes open for scratches. After finishing off with the polish, grease removal as well as waxing, you are almost done, hopefully with things looking good for your car. You now have the completed section and should be ready to plate it using chrome and nickel. Following that, install it and you are done with your nice looking and sturdy bumper, which should really be worth your time and effort!